DCBX - Show / manipulate DCBX configuration
lldptool -t -i ethx -V IEEE-DCBX -c [mode]
lldptool -T -i ethx -V IEEE-DCBX mode=reset
lldptool -t -i ethx -V <CIN-DCBX|CEE-DCBX> -c [enableTx]
lldptool -T -i ethx -V <CIN-DCBX|CEE-DCBX> enableTx=<yes|no>
lldpad supports the following versions of the DCB capabilities exchange (DCBX) protocol:
See the IEEE 802.1Qaz-2011 specification for details.”
IEEE DCBX is the default DCBX mode for a DCB capable interface. Therefore the default and configured IEEE DCBX TLV's will be transmitted when the interface comes up. lldpad can be globally configured to support one of the legacy DCBX versions (CIN or CEE). If the remote LLDP agent does not transmit any IEEE DCBX TLV's and does transmit a legacy DCBX TLV which matches the configured legacy DCBX version, then the DCBX mode will drop back to legacy DCBX mode. It will not transition back to IEEE DCBX mode until the next link reset. If lldpad has dropped back to legacy DCBX mode for a given interface and the daemon is stopped and restarted, the legacy DCBX mode for that interface will be used instead of starting out in IEEE DCBX mode. This behavior only applies to the case where lldpad is restarted and is not persistent across a system reboot.
The DCBX mode can be queried and configured by using the special tlvid IEEE-DCBX. There is not an actual TLV which corresponds to this tlvid. It's use is to query and reset the IEEE DCBX mode. When queried, IEEE DCBX mode can take the following values:
auto - IEEE DCBX will be used (intially) if lldpad is restarted
CEE - CEE DCBX will be used if lldpad is restarted
CIN - CIN DCBX will be used if lldpad is restarted
The IEEE DCBX mode can be reset to auto by setting the mode argument to the value reset
The detailed configuration of the CIN and CEE DCBX TLV's is performed using dcbtool (see dcbtool(8)). However, lldptool can configure the enableTx parameter of the CIN and CEE DCBX TLV's (as it can with most other TLV's). Since lldpad only transmits TLV's for one version of DCBX on any given interface, the enableTx parameter for the CIN and CEE DCBX TLV's (and for the IEEE DCBX feature TLV's) takes effect only when the corresponding DCBX version is active.
mode=reset Reset the DCBX mode that will be used if lldpad is restarted by setting the mode argument to reset using the special tlvid IEEE-DCBX.
enableTx Enable the specified DCBX TLV (CIN-DCBX or CEE-DCBX) to be transmitted in the LLDPDU if that DCBX mode for the specified interface has been selected.
Query the current DCBX mode that will be used if lldpad is restarted. (this is not a persistent setting)
lldptool -t -i eth3 -V IEEE-DCBX -c mode
Reset the DCBX mode to be 'auto' (start in IEEE DCBX mode) after the next lldpad restart
lldptool -T -i eth3 -V IEEE-DCBX mode=reset
Enable transmission of the CEE DCBX TLV lldptool -T -i eth3 -V CEE-DCBX enableTx=yes
Disable transmission of the CIN DCBX TLV lldptool -T -i eth3 -V CIN-DCBX enableTx=no
Query the configuration of enableTx for the CEE DCBX TLV
lldptool -t -i eth3 -V CEE-DCBX -c enableTx
This document was created by man2html, using the manual pages.
Time: 20:18:51 GMT, January 24, 2013